How to assemble IKEA STORKLINTA 4-Drawer Dresser

Step-by-step assembly

1. 

   Step 1 · manual step 1–2

   Screw the runners onto both side panels — 24 screws (146114).

   CL runners on one side, CR on the other. Then turn the 4 grey latches as shown.

   ▶ Watch this step (0:21)

2. 

   Step 2 · manual step 3–5

   4 cam bolts and 2 screws (105248) into the sides; fix the wall bracket.

   Leave a small gap under the 105248 heads. Bracket 106989: screw 109049 + washer 100823.

   ▶ Watch this step (0:29)

3. 

   Step 3 · manual step 6–8

   Dowels in the bottom panel; stand it on one side; lock with 2 cam locks.

   4 dowels (101345). Cam locks 119252/119250 — not the 120076 drawer cam locks.

   ▶ Watch this step (0:38)

4. 

   Step 4 · manual step 9–10

   Fit the second side panel and lock it with 2 cam locks.

   The unit now lies on its back. Cam locks 119252/119250, turned clockwise.

   ▶ Watch this step (0:47)

5. 

   Step 5 · manual step 11

   Clip the drawer-interlock rod (10076617) onto the right side.

   Lock its 2 clips as shown in the manual, step 11.

   ▶ Watch this step (0:55)

6. 

   Step 6 · manual step 12–13

   Screw 2 brackets (102553) to the plinth rail, then fix it to the sides.

   4 screws (105248): 2 into the rail, 2 into the side panels.

   ▶ Watch this step (1:01)

7. 

   Step 7 · manual step 14

   Press in the 2 L-shaped feet (10101849) and 2 straight ones (158568).

   L-shaped at the plinth corners, straight ones at the back.

   ▶ Watch this step (1:09)

8. 

   Step 8 · manual step 15–16

   Push 4 dowels into the side tops; 4 cam bolts into the top panel.

   Dowels 101345, cam bolts 118331.

   ▶ Watch this step (1:14)

9. 

   Step 9 · manual step 17–18

   Push the top on and lock it with 4 cam locks (119252).

   Turn the cam locks clockwise.

   ▶ Watch this step (1:21)

10. 

    Step 10 · manual step 19–20

    Push 6 dowels into the top rail and back panel, then join them.

    Dowels 101345 — push the rail fully against the panel, as the manual shows.

    ▶ Watch this step (1:29)

11. 

    Step 11 · manual step 21

    Turn the unit onto its side and slide in the upper back panel.

    Check that the frame is square before you slide the panel in.

    ▶ Watch this step (1:36)

12. 

    Step 12 · manual step 22–23

    Slide in the lower back panel and fix it with 2 plastic rivets.

    Push in rivet 10094727, then press its pin 10094763 in.

    ▶ Watch this step (1:44)

13. 

    Step 13 · manual step 24

    Stand the unit upright.

    ▶ Watch this step (1:52)

14. 

    Step 14 · manual step 24

    Fit 6 clips to the back panels from the inside.

    Push clip 10093081 in, then press insert 10093082 into it.

    ▶ Watch this step (1:58)

15. 

    Step 15 · manual step 25–26

    Swing out the anti-tip fitting; slide the wall bracket back.

    Loosen screw 109049, push the bracket to the wall, tighten it — see the manual, step 26.

    ▶ Watch this step (2:02)

16. 

    Step 16 · manual step 26–28

    Mark the holes on the wall, move the dresser away, drill and fit 2 plugs.

    Plugs 10087223 suit most solid and hollow walls. Solid wood: screws without plugs.

    ▶ Watch this step (2:10)

17. 

    Step 17 · manual step 29–30

    Push the dresser back; screw the fitting and bracket to the wall.

    2 screws (109572), washer 100823 on the bracket. Skirting board? Use spacer 10102070.

    ▶ Watch this step (2:17)

18. 

    Step 18 · manual step 31–32

    Drawers: 4 cam bolts in the front (face-down), 4 dowels in the sides.

    All 4 drawers are built the same way — here is one, step by step.

    ▶ Watch this step (2:24)

19. 

    Step 19 · manual step 33–34

    Stand the sides on the front and lock with 4 cam locks (120076).

    ▶ Watch this step (2:31)

20. 

    Step 20 · manual step 35–36

    Slide in the drawer bottom; tap the wire (10040242) into the drawer back.

    Check the wire’s direction against the manual, step 36.

    ▶ Watch this step (2:38)

21. 

    Step 21 · manual step 37–38

    Put the back on; push in 4 pegs (145718) and lock 4 cam locks (120076).

    ▶ Watch this step (2:44)

22. 

    Step 22 · manual step 39

    Turn the drawer over and screw on its runners — 6 screws (146114).

    Match the drawer runners to the CL / CR runners in the frame.

    ▶ Watch this step (2:51)

23. 

    Step 23 · manual step 31–39

    Build the other 3 drawers the same way.

    ▶ Watch this step (2:58)

24. 

    Step 24 · manual step 40–41

    Slide the drawers onto the runners.

    Open only one drawer at a time — the interlock stops the others.

    ▶ Watch this step (3:03)