How to assemble IKEA RÅDMANSÖ 6-Drawer Dresser

Step-by-step assembly

1. 

   Step 1 · manual step 1–2

   Screw 3 runners (CR) onto the divider, turn it over, then 3 runners (CL).

   9 screws (10047245) on each face.

   ▶ Watch this step (0:21)

2. 

   Step 2 · manual step 3

   Hang the divider on the top panel and press it down until it clicks.

   ▶ Watch this step (0:29)

3. 

   Step 3 · manual step 4

   Screw 3 runners onto the inside of each side panel.

   CL on one side, CR on the other — 9 screws (10047245) each.

   ▶ Watch this step (0:35)

4. 

   Step 4 · manual step 5

   Hang both side panels on the ends of the top panel.

   Press them down until they click.

   ▶ Watch this step (0:42)

5. 

   Step 5 · manual step 6–7

   Lay the back panel in. Push the bottom panel on until it clicks.

   The back panel’s edges rest in the rebates of the sides.

   ▶ Watch this step (0:49)

6. 

   Step 6 · manual step 8–9

   Drive in 2 screws (105251) with the hex key.

   Then push 2 inserts (10075558) into the back panel and press a pin (10051084) into each.

   ▶ Watch this step (0:56)

7. 

   Step 7 · manual step 10

   Join the 2 leg frames with the 2 rails — 4 bolts (10003283).

   Use the hex key. The frame is upside down.

   ▶ Watch this step (1:04)

8. 

   Step 8 · manual step 11

   Roll the carcass onto its top. Fix the leg frame with 4 bolts (10120564).

   ▶ Watch this step (1:11)

9. 

   Step 9 · manual step 12

   Screw the 4 feet (10121698 + 10114605) into the legs, then turn it upright.

   ▶ Watch this step (1:20)

10. 

    Step 10 · manual step 13–14

    Fit 2 wall fittings (150688) at the back, then 8 fittings (10093081).

    Press a pin (10093082) into each of the 8 fittings.

    ▶ Watch this step (1:29)

11. 

    Step 11 · manual step 15–16

    Push 4 dowels (101345) into the strip, then press it down at the back.

    ▶ Watch this step (1:37)

12. 

    Step 12 · manual step 17

    Push 4 inserts (10075558) into the bottom and press in 4 pins (10051084).

    ▶ Watch this step (1:45)

13. 

    Step 13 · manual step 18

    Check it is level. Adjust the 4 feet with the spanner (190459).

    ▶ Watch this step (1:51)

14. 

    Step 14 · manual step 19–21

    Mark the 2 holes on the wall, move the dresser away and drill.

    Ø 8 mm, push in the plugs (10087223). Solid wood: Ø 3 mm, no plugs — see the manual.

    ▶ Watch this step (1:57)

15. 

    Step 15 · manual step 22

    Push it back. Screw it to the wall through both fittings.

    2 screws (109572) with washers (126916).

    ▶ Watch this step (2:05)

16. 

    Step 16

    Now the 6 drawers.

    All six are the same — we build one step by step.

    ▶ Watch this step (2:12)

17. 

    Step 17 · manual step 23–24

    Click both sides onto the drawer front, then slide the bottom down the grooves.

    ▶ Watch this step (2:15)

18. 

    Step 18 · manual step 25–26

    Press the wire fitting (10040242) into the back, then fit the back.

    It goes between the sides, over the bottom.

    ▶ Watch this step (2:23)

19. 

    Step 19 · manual step 27

    Push in 4 cam dowels (159553), then 4 cam locks (117434).

    Turn the cam locks clockwise.

    ▶ Watch this step (2:29)

20. 

    Step 20 · manual step 28

    Turn the drawer over. Screw on the runners DL and DR — 6 screws (10047245).

    ▶ Watch this step (2:37)

21. 

    Step 21 · manual step 29

    Fit the knob (10109447) with the screw (119976) from the inside.

    Use a screwdriver — not a drill.

    ▶ Watch this step (2:44)

22. 

    Step 22 · manual step 23–29

    Build the other 5 drawers the same way.

    ▶ Watch this step (2:50)

23. 

    Step 23 · manual step 30

    Slide the 6 drawers in on their runners.

    Open only one drawer at a time.

    ▶ Watch this step (2:55)