How to assemble IKEA SKRUVBY Cabinet with Doors

Step-by-step assembly

1. 

   Step 1

   Screw the 4 feet (152676) into the bottom panel.

   Lay the bottom panel upside-down on the rug.

   ▶ Watch this step (0:20)

2. 

   Step 2

   Turn it over and screw in 4 connectors (10047135).

   Screw them all the way in by hand — no thread may show.

   ▶ Watch this step (0:27)

3. 

   Step 3

   Push 8 dowels (101345) into the ends of the side panels.

   2 in each end.

   ▶ Watch this step (0:35)

4. 

   Step 4

   Stand both side panels onto the bottom panel.

   The connectors and dowels go into the holes in their lower ends.

   ▶ Watch this step (0:42)

5. 

   Step 5

   Insert 4 cam locks and turn them clockwise.

   Use a flat-head screwdriver — the lock grips the connector.

   ▶ Watch this step (0:50)

6. 

   Step 6

   Slide the back panel down into the grooves.

   Push it all the way down into the groove in the bottom panel.

   ▶ Watch this step (0:57)

7. 

   Step 7

   Screw 4 connectors (10047135) into the top panel.

   Underside up, all the way in by hand.

   ▶ Watch this step (1:03)

8. 

   Step 8

   Turn the top over and press it onto the side panels.

   ▶ Watch this step (1:10)

9. 

   Step 9

   Insert 4 cam locks at the top and turn them clockwise.

   ▶ Watch this step (1:17)

10. 

    Step 10

    Turn the cabinet round and fit the 10 back clips.

    Push in the clips (10093081), then lock each one with a 10093082.

    ▶ Watch this step (1:23)

11. 

    Step 11

    Fit the 2 wall fittings (150688) at the top of the back.

    Push their 2 pins into the holes in each side panel.

    ▶ Watch this step (1:32)

12. 

    Step 12 · manual step 12–13

    Skirting board on your wall? Fit the knobs (150689).

    Screw one onto each fitting and turn it to fit the gap — see the manual, steps 12–13.

    ▶ Watch this step (1:39)

13. 

    Step 13 · manual step 14

    Turn the 4 feet to level the cabinet.

    Check with a spirit level on the top.

    ▶ Watch this step (1:44)

14. 

    Step 14 · manual step 15–16

    Stand it against the wall and mark the 2 holes.

    Mark through the wall fittings, then move the cabinet away.

    ▶ Watch this step (1:51)

15. 

    Step 15 · manual step 17

    Drill the holes and fit plugs to suit your wall.

    Plugs (121714) for solid and hollow walls; none for solid wood — see manual p. 21–22.

    ▶ Watch this step (1:58)

16. 

    Step 16 · manual step 18

    Push it back and screw it to the wall through the fittings.

    Washer (126916) + screw 158469 — use the long 147968 if you fitted the knobs.

    ▶ Watch this step (2:06)

17. 

    Step 17 · manual step 19

    Snap the 2 covers (133303/133304) over the screw heads.

    ▶ Watch this step (2:14)

18. 

    Step 18 · manual step 20

    Push the 8 shelf supports (10075382) into the sides.

    4 per shelf, at the height you want.

    ▶ Watch this step (2:20)

19. 

    Step 19 · manual step 21

    Lay the 2 shelves on the supports.

    Check the edge detail in the manual, step 21, for the right way round.

    ▶ Watch this step (2:26)

20. 

    Step 20 · manual step 22

    Screw a hinge (10071303) into each door.

    Doors face-down; the hinge cups go in the round holes.

    ▶ Watch this step (2:33)

21. 

    Step 21 · manual step 23

    Hang the doors and screw the hinges to the side panels.

    2 screws per hinge. Easier with two people.

    ▶ Watch this step (2:40)

22. 

    Step 22 · manual step 24

    Fit a handle (130417) on each door.

    2 screws (100400) per handle, from the inside of the door.

    ▶ Watch this step (2:49)

23. 

    Step 23 · manual step 25

    Stick on the 2 bumpers (104663), then close the doors.

    Check where they go in the manual, step 25.

    ▶ Watch this step (2:56)