IKEA · Cabinets & Wardrobes

How to assemble IKEA NYSJÖN Mirror with Shelf

Step-by-step IKEA NYSJÖN Mirror with Shelf assembly: 10 illustrated steps, an animated video, the hardware list and the tools you need — following the official instructions (AA-2246804-3).

  • 10 illustrated steps
  • 9 steps in the manual
  • 1:46 video
  • 50×13×61 cm cm
IKEA NYSJÖN Mirror with Shelf, assembled

What you need

Tools

  • Flat-head screwdriver
  • Phillips screwdriver
  • Spirit level

You’ll need: a pencil, a tape measure, a spirit level and flat-head and Phillips screwdrivers.

Hardware in the box

Part no. (as printed in the manual)Qty
100620532×
1392982×
1392992×

Step-by-step assembly

  1. Step 1: Mark 4 points on the wall, using a spirit level. — IKEA NYSJÖN assembly

    Step 1

    Mark 4 points on the wall, using a spirit level.

    400 mm (15 3/4") apart; the top marks 575 mm (22 5/8") above the bottom ones.

  2. Step 2: Press 6 pads (107091) onto the 2 brackets (10062053). — IKEA NYSJÖN assembly

    Step 2

    Press 6 pads (107091) onto the 2 brackets (10062053).

    3 on each bracket — 2 at the holder end, 1 at the front.

  3. Step 3: Hold each bracket against the wall at a bottom mark. — IKEA NYSJÖN assembly

    Step 3

    Hold each bracket against the wall at a bottom mark.

  4. Step 4: Fix each bracket with 1 screw through the holder. — IKEA NYSJÖN assembly

    Step 4 · manual step 3

    Fix each bracket with 1 screw through the holder.

    Wall screws and plugs are not included — use ones suited to your wall.

  5. Step 5: Peel the strip (120040) and put a pad into each holder. — IKEA NYSJÖN assembly

    Step 5 · manual step 4

    Peel the strip (120040) and put a pad into each holder.

    The pad goes against the back of the holder — see the manual, step 4.

  6. Step 6: Screw the 2 discs (139299) to the wall at the top marks. — IKEA NYSJÖN assembly

    Step 6 · manual step 5

    Screw the 2 discs (139299) to the wall at the top marks.

    Round-head screws (not included), max. 3.5 mm (1/8") left out. No power screwdriver.

  7. Step 7: Push the 2 clips (139298) up onto the discs. — IKEA NYSJÖN assembly

    Step 7 · manual step 6

    Push the 2 clips (139298) up onto the discs.

  8. Step 8: Push the clips up, then set the mirror into the 2 holders. — IKEA NYSJÖN assembly

    Step 8 · manual step 7

    Push the clips up, then set the mirror into the 2 holders.

    Bottom edge into the holders first, then tip it back against the wall.

  9. Step 9: Push both clips down over the top edge of the mirror. — IKEA NYSJÖN assembly

    Step 9 · manual step 8

    Push both clips down over the top edge of the mirror.

  10. Step 10: Slide the shelf onto the brackets from the side. — IKEA NYSJÖN assembly

    Step 10 · manual step 9

    Slide the shelf onto the brackets from the side.

    It lies between the mirror and the bracket lips — from either side, see the manual, step 9.

Tips & safety

  • Wall mounting should be done by a qualified person. Screws and plugs are not included — choose ones suited to your wall that can carry the mirror. If unsure, ask a specialist.
  • Mirror not level? Turn the discs (139299) on their screws to raise or lower each side — see the manual, step 5.

Official instructions

This guide follows IKEA’s official assembly instructions (AA-2246804-3). Keep the printed manual to hand — if anything differs, the manual is right.

Open the official PDF manual

More guides: Cabinets & Wardrobes