How to assemble IKEA NYSJÖN Laundry Cabinet

Step-by-step assembly

1. 

   Step 1

   Screw the 4 wall brackets (10032274) onto the side panels.

   2 screws (10048881) per bracket — one bracket at each end of each panel.

   ▶ Watch this step (0:18)

2. 

   Step 2

   Screw 16 cam bolts (123492) into the side panels.

   8 in each panel.

   ▶ Watch this step (0:25)

3. 

   Step 3

   Push 16 dowels (101375) into the edges of the 4 short panels.

   2 in each long edge.

   ▶ Watch this step (0:31)

4. 

   Step 4

   Stand the 4 short panels on the side panel.

   Top, bottom and 2 shelves — the cam bolts and dowels go into the holes.

   ▶ Watch this step (0:37)

5. 

   Step 5

   Insert 8 cam locks (102509) and turn them clockwise.

   Use the flat-head screwdriver.

   ▶ Watch this step (0:44)

6. 

   Step 6

   Lay the other side panel on top.

   Its cam bolts go into the holes in the short panels.

   ▶ Watch this step (0:50)

7. 

   Step 7

   Insert 8 more cam locks (102509) and turn them clockwise.

   ▶ Watch this step (0:56)

8. 

   Step 8

   Turn the carcass onto its front and lay the back panel on.

   ▶ Watch this step (1:02)

9. 

   Step 9 · manual step 9–11

   Nail 3 corners first, using the nail holder (105494).

   Line up each corner of the back panel with the carcass before you nail it.

   ▶ Watch this step (1:08)

10. 

    Step 10 · manual step 12

    Hammer in the other 27 nails all around the edge.

    ▶ Watch this step (1:16)

11. 

    Step 11 · manual step 13

    Turn it onto its back. Screw on the 2 legs (10059781).

    2 screws (124431) per leg, at the front corners of the bottom.

    ▶ Watch this step (1:22)

12. 

    Step 12 · manual step 14

    Screw the 2 adjustable feet (10056734) into the legs.

    ▶ Watch this step (1:30)

13. 

    Step 13 · manual step 15

    Stand the cabinet up against the wall. Level it with the feet.

    Turn the feet to adjust the height until the cabinet is level.

    ▶ Watch this step (1:36)

14. 

    Step 14 · manual step 16

    Mark the 4 bracket holes on the wall, then move the cabinet away.

    Mark with a pencil through the square opening in each bracket.

    ▶ Watch this step (1:43)

15. 

    Step 15 · manual step 17

    Drive 4 screws into the wall at the marks.

    Not included — use pan-head screws suited to your wall; leave the heads sticking out.

    ▶ Watch this step (1:49)

16. 

    Step 16 · manual step 18

    Clip the 4 plates (153647) onto the brackets and hang the cabinet.

    The screw heads go through the keyholes. Adjust the brackets, then tighten.

    ▶ Watch this step (1:56)

17. 

    Step 17 · manual step 19

    Snap the 4 covers (10043569) over the brackets.

    2 at the bottom and 2 at the top.

    ▶ Watch this step (2:04)

18. 

    Step 18 · manual step 20

    Screw the 3 hinges (144553) onto the back of the door.

    The door can hang on the left or the right — check the hole positions in the manual first.

    ▶ Watch this step (2:10)

19. 

    Step 19 · manual step 21

    Hang the door on the left side panel and tighten the hinge screws.

    ▶ Watch this step (2:17)

20. 

    Step 20 · manual step 22

    Click the 2 rings (123056) into the round openings in the door.

    Each ring has a front and a back part that click together.

    ▶ Watch this step (2:25)

21. 

    Step 21 · manual step 23

    Press the 3 covers (139244) into the unused hinge holes.

    On the back of the door, along the edge without hinges.

    ▶ Watch this step (2:31)

22. 

    Step 22 · manual step 24–25

    Drill the knob hole (ø 5 mm), 30 mm from the edge. Fit the knob (106266).

    At the middle hinge height. The screw (119976) goes through the door from the back.

    ▶ Watch this step (2:37)

23. 

    Step 23 · manual step 26

    Stick the 2 bumpers (107091) on the back of the door.

    Near the top and bottom corners of the free edge.

    ▶ Watch this step (2:46)

24. 

    Step 24 · manual step 27

    Screw the 2 stops (123029) onto the left side panel.

    Beside the middle and bottom hinges, 1 screw (124431) each — mark the holes with an awl first.

    ▶ Watch this step (2:52)

25. 

    Step 25 · manual step 28–29

    Unfold the 2 laundry bags and put them in the cabinet.

    Push the bottom board into each bag first — see the manual, step 28.

    ▶ Watch this step (2:59)