How to assemble IKEA MOSSJÖN Glass-Door Cabinet with 2 Doors

Step-by-step assembly

1. 

   Step 1 · manual step 1–2

   Lay one long frame on the rug. Push in the 4 short rails.

   They click into the clips: 2 at the top end, then 2 at the middle rail.

   ▶ Watch this step (0:19)

2. 

   Step 2 · manual step 3

   Fix the short rails with 4 screws (10075024).

   Use the Phillips screwdriver.

   ▶ Watch this step (0:27)

3. 

   Step 3 · manual step 4

   Lower the second long frame onto the short rails.

   ▶ Watch this step (0:34)

4. 

   Step 4 · manual step 5–6

   Fit 2 Allen screws (10082207) at the top, 2 screws (10075024) at the middle.

   Use the small Allen key 100092 for the top ones.

   ▶ Watch this step (0:39)

5. 

   Step 5 · manual step 7

   Screw an adjustable foot (10099819) into each of the 4 legs.

   ▶ Watch this step (0:48)

6. 

   Step 6 · manual step 8

   Put the 2 open shelves into the lower section.

   In between the rails, then slide each one down to its rail.

   ▶ Watch this step (0:54)

7. 

   Step 7 · manual step 9

   Fix the shelves with 4 screws (144451).

   Two per shelf, through the lips into the rails.

   ▶ Watch this step (1:01)

8. 

   Step 8 · manual step 9

   Turn the frame over.

   ▶ Watch this step (1:08)

9. 

   Step 9 · manual step 10

   Fix the shelves on this side with 4 more screws (144451).

   ▶ Watch this step (1:12)

10. 

    Step 10 · manual step 11

    Stand the frame upright.

    ▶ Watch this step (1:18)

11. 

    Step 11

    Lower the cabinet bottom into place on its pins.

    Check which way round it goes — see the manual, step 11.

    ▶ Watch this step (1:23)

12. 

    Step 12

    Fit the two glass side panels into the upper section.

    ▶ Watch this step (1:28)

13. 

    Step 13

    Fix the side panels with 7 screws (144451).

    4 in the left panel, 3 in the right — check the holes in the manual, step 13.

    ▶ Watch this step (1:35)

14. 

    Step 14

    Fit 2 hinge bushings (10004350) to each door, 1 screw (10108237) each.

    At the top and bottom ends of the hinge side.

    ▶ Watch this step (1:42)

15. 

    Step 15

    Slide a handle (10103731) onto each door. Fix it with 2 screws (10103596).

    ▶ Watch this step (1:49)

16. 

    Step 16

    Push a pivot pin (107832) into each front corner. Add a washer (102319).

    ▶ Watch this step (1:57)

17. 

    Step 17

    Set each door onto its pivot pin and tip it in at the top.

    ▶ Watch this step (2:03)

18. 

    Step 18

    Screw the 2 top pivot pins (10103598) down into the doors.

    Use the long Allen key 10089605. Screw them in flush — not sticking up.

    ▶ Watch this step (2:11)

19. 

    Step 19 · manual step 19–20

    Turn the top over and lay it on. Fix it with 4 screws (144451).

    See the manual, step 20 for the 4 holes.

    ▶ Watch this step (2:17)

20. 

    Step 20 · manual step 21–22

    Fit the glass back panel. Fix it with 8 screws (144451).

    ▶ Watch this step (2:26)

21. 

    Step 21 · manual step 23–25

    Mark the top and side on the wall. Screw the strap (107967) to the wall.

    7.6 cm below the top mark, 2.5 cm in from the side, through washer 100823. Wall screws not included.

    ▶ Watch this step (2:35)

22. 

    Step 22 · manual step 26–27

    Push the cabinet back. Feed the strap into the slot and screw it on (144451).

    The screw goes in from inside the cabinet, on the back post.

    ▶ Watch this step (2:44)

23. 

    Step 23 · manual step 28

    Screw 8 shelf supports (10103727) into the side panels.

    Use the long Allen key 10089605. Pick your shelf heights.

    ▶ Watch this step (2:53)

24. 

    Step 24 · manual step 29

    Lay in the 2 shelves (10103654). Close the doors.

    ▶ Watch this step (2:59)

25. 

    Step 25 · manual step 30

    Turn the feet until the cabinet is level.

    Check with a spirit level on top.

    ▶ Watch this step (3:08)