How to assemble IKEA LOMMARP Cabinet

Step-by-step assembly

1. 

   Step 1 · manual step 1–2

   Base: screw 4 cam bolts (100481) into the 2 side pieces.

   Then push 4 dowels (101345) into the ends of the front piece.

   ▶ Watch this step (0:26)

2. 

   Step 2 · manual step 3–5

   Join the 3 pieces and lock them with 4 cam locks.

   Turn the locks clockwise. Then push 7 dowels into the top edges.

   ▶ Watch this step (0:32)

3. 

   Step 3 · manual step 6–8

   Screw 4 brackets (103717) onto the back rail; push in 3 dowels.

   Then turn 12 cam bolts (100481) into the board — check its edge in the manual, step 6.

   ▶ Watch this step (0:40)

4. 

   Step 4 · manual step 9–10

   Turn the frame over and press it onto the board.

   Fit the back rail between the side pieces at the same time.

   ▶ Watch this step (0:48)

5. 

   Step 5 · manual step 11–12

   Press the 4 corner pads onto the legs. Screw the brackets tight.

   Pads 10006536 (A) and 10006543 (B). 4 screws (100347) through the brackets.

   ▶ Watch this step (0:54)

6. 

   Step 6 · manual step 13–14

   Lock with 12 cam locks, then turn the base over.

   Turn 4 cam bolts (118331) into the board — bag 2 starts here.

   ▶ Watch this step (1:01)

7. 

   Step 7 · manual step 15–16

   Turn 4 cam bolts (118331) into the 2 side panels.

   Push 4 dowels (101345) into the ends of the fixed shelf.

   ▶ Watch this step (1:09)

8. 

   Step 8 · manual step 17–19

   Join the sides and the fixed shelf, lying on their back edges.

   Lock with 4 cam locks (103430), turned clockwise.

   ▶ Watch this step (1:15)

9. 

   Step 9 · manual step 20

   Push 8 dowels into the panel ends and stand it up.

   2 dowels in each end of both side panels.

   ▶ Watch this step (1:22)

10. 

    Step 10 · manual step 21–22

    Lower the cabinet onto the base. Lock with 4 cam locks.

    The cam bolts in the board go into the side panels.

    ▶ Watch this step (1:28)

11. 

    Step 11 · manual step 23–25

    Fit the middle divider on 2 cam bolts and 4 dowels.

    Cam bolts 118331 in the fixed shelf; lock with 2 cam locks.

    ▶ Watch this step (1:35)

12. 

    Step 12 · manual step 26–29

    Build the rear rail and slide it in at the back, at the bottom.

    2 dowels (101349), 1 screw (109060). Then 4 fittings (10043826) in the sides.

    ▶ Watch this step (1:43)

13. 

    Step 13 · manual step 30

    Slide the back panel down into the grooves.

    Its lower edge goes into the groove in the rear rail.

    ▶ Watch this step (1:51)

14. 

    Step 14 · manual step 31–33

    Turn 6 cam bolts (118331) into the top and fit it.

    Lock it with 6 cam locks — in both sides and the divider.

    ▶ Watch this step (1:56)

15. 

    Step 15 · manual step 34–35

    Fix the back panel with 4 plugs and 8 clips.

    Plugs 151708 + 151707 along the shelf; clips 10093081 + 10093082 at the edges.

    ▶ Watch this step (2:04)

16. 

    Step 16 · manual step 36

    Screw the 2 drawer runners to the side panels.

    2 screws (100347) in each runner.

    ▶ Watch this step (2:10)

17. 

    Step 17 · manual step 37–39

    Fix the cabinet to the wall with the 2 brackets (106989).

    Screw 109049 + washer into the top, then wall screws 109048 + washer (plugs 121714 if needed).

    ▶ Watch this step (2:15)

18. 

    Step 18 · manual step 40–41

    Press in 16 shelf supports (131372). Lay in the 4 shelves.

    2 shelves in each compartment.

    ▶ Watch this step (2:22)

19. 

    Step 19 · manual step 42–44

    Doors face down: press in 4 bumpers (107586), screw on the hinges.

    Hinges 10031762 on one door, 10031756 on the other — see the manual, steps 43–44.

    ▶ Watch this step (2:29)

20. 

    Step 20 · manual step 45–46

    Hang the doors and tighten the hinge screws. Fit the 2 handles.

    Handles 10006275 with screws 151743 — not the longer 119976.

    ▶ Watch this step (2:36)

21. 

    Step 21 · manual step 47–49

    Drawer: 4 cam bolts (118331) in the front, 4 dowels in the sides.

    Stand the sides on the front and lock with 4 cam locks (112399).

    ▶ Watch this step (2:44)

22. 

    Step 22 · manual step 50–53

    Slide in the bottom. Fit the back on 4 cam bolts (118331).

    Lock it with 4 cam locks (112399).

    ▶ Watch this step (2:51)

23. 

    Step 23 · manual step 54–57

    Press in 2 bumpers (107586), turn the drawer over, fit 2 knobs.

    Knobs 10006309 with screws 119976. Steps 55–56: fit the bar with 3 screws (105344).

    ▶ Watch this step (2:59)

24. 

    Step 24 · manual step 58–59

    Put the drawer on the runners and push it in.

    Lock it to the runners with the 2 clips (124218) underneath.

    ▶ Watch this step (3:07)