How to assemble IKEA HAUGA Glass-Door Cabinet

Step-by-step assembly

1. 

   Step 1

   Fit the bottom panel to the end of the divider. Press until it clicks.

   The cabinet is built lying on its front. 2 click fittings.

   ▶ Watch this step (0:20)

2. 

   Step 2

   Fit the top panel to the other end of the divider. Press until it clicks.

   2 click fittings.

   ▶ Watch this step (0:26)

3. 

   Step 3 · manual step 3–4

   Click on both side panels — 4 fittings each.

   Push each side on, then press it down until it clicks. The curved corner goes at the top front.

   ▶ Watch this step (0:32)

4. 

   Step 4 · manual step 5

   Slide the back panel into the grooves from the bottom end.

   It folds out to full size. Push it all the way to the top panel.

   ▶ Watch this step (0:40)

5. 

   Step 5 · manual step 6

   Push 8 plugs (151708) through the back panel.

   Into the holes over the top, bottom and divider.

   ▶ Watch this step (0:46)

6. 

   Step 6 · manual step 7–8

   Fit 8 clips along the side edges, then push 8 pins (151707) into the plugs.

   Clips 10093081 + caps 10093082 — positions in the manual, step 7.

   ▶ Watch this step (0:52)

7. 

   Step 7 · manual step 9

   Fit the 2 wall spacers (150688) at the top corners of the back.

   They are used to fix the cabinet to the wall later.

   ▶ Watch this step (1:00)

8. 

   Step 8 · manual step 10

   Push 6 dowels (101345) into the 2 plinth rails and fit them at the bottom.

   ▶ Watch this step (1:06)

9. 

   Step 9 · manual step 11–12

   Press the 6 feet into the rails.

   4 corner feet (10040039) at the ends, 2 feet (153548) in the middle.

   ▶ Watch this step (1:13)

10. 

    Step 10 · manual step 13

    Raise the cabinet upright.

    ▶ Watch this step (1:19)

11. 

    Step 11 · manual step 13

    Push 3 dowels (101345) into the top panel and press the top board on.

    Push the dowels in by hand — no hammer.

    ▶ Watch this step (1:24)

12. 

    Step 12 · manual step 14

    Fix the top board with 2 plugs (151708) and 2 pins (151707).

    From the back, one at each end.

    ▶ Watch this step (1:31)

13. 

    Step 13 · manual step 15–17

    Place the cabinet against the wall and mark the 2 spacer holes.

    Skirting board? First screw the 2 knobs (150689) onto the spacers, then turn them out until they touch the wall — steps 15–16.

    ▶ Watch this step (1:38)

14. 

    Step 14 · manual step 18–19

    Move the cabinet away, drill 2 holes at the marks and tap in the plugs.

    Plugs 121714 suit most walls. Drill size and solid wood: see the manual, step 19.

    ▶ Watch this step (1:46)

15. 

    Step 15 · manual step 20

    Push it back and screw it to the wall through the 2 spacers.

    Screw 158469 + washer 126916 (147968 if you fitted the knobs). Then click on the caps (133303).

    ▶ Watch this step (1:52)

16. 

    Step 16 · manual step 21

    Press the 2 bottom tracks (10047003) into the grooves of the bottom panel.

    Start at one end and press them in bit by bit.

    ▶ Watch this step (1:59)

17. 

    Step 17 · manual step 22

    Press the 2 top tracks (10047009) into the grooves under the top panel.

    The same way, from one end to the other.

    ▶ Watch this step (2:05)

18. 

    Step 18 · manual step 23

    Push 24 shelf supports (10051650) into the sides and divider.

    4 for each shelf, at the height you want.

    ▶ Watch this step (2:10)

19. 

    Step 19 · manual step 24

    Press 4 door bumpers (115339) into the side panels.

    Near the front edge, at the top and bottom of each side.

    ▶ Watch this step (2:17)

20. 

    Step 20 · manual step 25–26

    Fit 2 top guides (192157) and 2 rollers (150521) to each door.

    Lock each fitting with 2 pins (192158). Lay the doors face-down.

    ▶ Watch this step (2:23)

21. 

    Step 21 · manual step 27–28

    Hang the first door on the back track, then the second on the front.

    Top into the top track, bottom onto the bottom track, then press the 2 locks until they click.

    ▶ Watch this step (2:31)

22. 

    Step 22 · manual step 29

    Fit a door stop (192161) at the top and bottom, then lock with pins.

    Slide the doors aside first. Exact positions and pins (192158): see the manual, step 29.

    ▶ Watch this step (2:40)

23. 

    Step 23 · manual step 30

    Screw a knob (10052019) onto each door.

    1 screw (119976) per knob, from the back of the door.

    ▶ Watch this step (2:48)

24. 

    Step 24 · manual step 31

    Slide the doors aside and lay the 6 shelves on the supports.

    3 in each half.

    ▶ Watch this step (2:54)