IKEA · Cabinets & Wardrobes
How to assemble IKEA ENHET Wall Cabinet with 2 Shelves
Step-by-step IKEA ENHET Wall Cabinet with 2 Shelves assembly: 15 illustrated steps, an animated video, the hardware list and the tools you need — following the official instructions (AA-2288902-2).
- 15 illustrated steps
- 19 steps in the manual
- 2:31 video
- 60×30×75 cm
What you need
Tools
- Phillips screwdriver
- Flat-head screwdriver
- Spirit level
- Hammer
- Drill (for wall fixing)
You’ll need: Phillips and flat-head screwdrivers, a pencil, a spirit level, a hammer, a clamp and a drill for the wall.
Hardware in the box
| Part no. (as printed in the manual) | Qty |
|---|---|
| 114667 | 2× |
| 151931 | 4× |
| 101375 | 4× |
| 151705 | 8× |
| 151706 | 8× |
| 10043826/10046078 | 8× |
| 10032274 | 2× |
| 153647 | 2× |
Step-by-step assembly
Step 1
Screw a wall bracket (10032274) onto each side panel.
2 screws (151931) per bracket, in the corner at the top end and back edge.
Step 2
Hook the top panel onto the end of one side panel.
Lower its 2 pegs into the keyhole slots, then push it to lock.
Step 3
Push 4 dowels (101375) into the ends of the rail.
2 in each end.
Step 4
Push the rail into the side panel, right below the top.
It goes at the back edge, next to the bracket.
Step 5
Hook the bottom panel onto the other end the same way.
Pegs into the keyhole slots, then push it to lock.
Step 6
Lay the other side panel on top.
4 pegs into the keyhole slots and the dowels into the holes — then push it to lock.
Step 7
Turn it onto its front. Slide the back panel into the grooves.
Push it in from the bottom end until its 2 large holes line up with the rail.
Step 8
Fix the back with 8 plastic plugs (151706) and pins (151705).
Push in the plugs, then press a pin into each — 4 at the top, 4 at the bottom.
Step 9
Stand the cabinet up and lift it to the wall.
Two people.
Step 10 · manual step 9–10
Hold it level against the wall. Mark through the 2 brackets.
Two people. On a stud wall, both screws must go into studs — see the manual, p. 10–11.
Step 11 · manual step 11–12
Move it away. Drill and drive 2 screws into the wall at the marks.
Not included: round-head screws, min. 3/16" thick and 1 1/2" into the wood. Leave the heads out.
Step 12 · manual step 13
Hang it on the screws and fit a plate (153647) into each bracket.
Adjust it sideways and up/down, then tighten with the screwdriver.
Step 13 · manual step 14
Press the 2 covers onto the brackets.
Step 14 · manual step 18
Press in the 8 shelf supports (10043826).
4 for each shelf, at the height you want.
Step 15 · manual step 19
Slide in the 2 shelves.
Lay each one on its 4 supports.
Tips & safety
- The doors are sold separately. The 4 hinges (10038769) and the bumpers (104663) in the box are for 2 ENHET doors — fit them as in manual steps 15–17.
- Use wall screws that suit your wall. Not included. Stud wall: steps 9–14; brick or concrete: manual p. 16–18. If unsure, ask a specialist.
- Two cabinets side by side? Join them with the 2 screws (114667) — see the manual, p. 19.
Official instructions
This guide follows IKEA’s official assembly instructions (AA-2288902-2). Keep the printed manual to hand — if anything differs, the manual is right.
