How to assemble IKEA EKET Cabinet with Door and Shelf

Step-by-step assembly

1. 

   Step 1

   Sort the four frame panels.

   The two short panels have pegs, the two long side panels have keyhole slots.

   ▶ Watch this step (0:20)

2. 

   Step 2

   Screw the push-opener (139468) to a side panel with 2 screws (108444).

   Then push the plunger (139467) into it until it clicks.

   ▶ Watch this step (0:26)

3. 

   Step 3

   Stand the other side panel on edge and slide a peg panel down onto it.

   The 3 pegs go into the keyhole slots — press down firmly.

   ▶ Watch this step (0:34)

4. 

   Step 4

   Slide the side panel with the push-opener down onto the pegs.

   ▶ Watch this step (0:43)

5. 

   Step 5

   Slide the back panel into the grooves.

   Make sure it runs in the grooves, not on top of them.

   ▶ Watch this step (0:50)

6. 

   Step 6

   Slide the last peg panel down to close the frame, then turn it upright.

   ▶ Watch this step (0:57)

7. 

   Step 7

   Push the back panel all the way down into the bottom groove.

   ▶ Watch this step (1:06)

8. 

   Step 8

   Fit 8 clips (10093081) around the back panel.

   Start at the bottom centre. Then press a wedge (10093082) into each clip.

   ▶ Watch this step (1:12)

9. 

   Step 9

   Fit legs or a suspension rail — follow its own manual.

   Legs and suspension rail are sold separately.

   ▶ Watch this step (1:21)

10. 

    Step 10

    Press 2 wall connectors (141413) into the back, just below the top.

    Door on the right, as here? Then panel 1 goes at the bottom — see the manual, step 10.

    ▶ Watch this step (1:28)

11. 

    Step 11

    Drill through the back panel at each connector with a Ø 8 mm bit.

    Ø 8 mm = 5/16".

    ▶ Watch this step (1:36)

12. 

    Step 12

    Turn a knob (141414) onto each connector.

    Turn it clockwise.

    ▶ Watch this step (1:42)

13. 

    Step 13

    Move the cabinet to the wall.

    Turn both knobs until they touch the wall, clear of the skirting board.

    ▶ Watch this step (1:48)

14. 

    Step 14

    Screw through each plate (152651) into the wall.

    Wall screws are not included — choose screws for your wall type.

    ▶ Watch this step (1:55)

15. 

    Step 15

    Press a cover cap (152650) onto each plate and turn it to lock.

    ▶ Watch this step (2:04)

16. 

    Step 16

    Push in 4 shelf pins (131372) and lay the shelf on them.

    The shelf must not stick out past the front edge (manual step 16).

    ▶ Watch this step (2:10)

17. 

    Step 17

    Press 2 hinge bushings (10119600) into the top and bottom panels.

    At the front corner on the hinge side.

    ▶ Watch this step (2:19)

18. 

    Step 18

    Click a hinge arm (10119658) into each bushing.

    ▶ Watch this step (2:25)

19. 

    Step 19

    Screw the washer (101313) and a screw (108444) into the door.

    Lay the door down inside face up.

    ▶ Watch this step (2:31)

20. 

    Step 20

    Push the hinge pins into the door: 139477 on top, 133127 below.

    ▶ Watch this step (2:39)

21. 

    Step 21

    Set the door onto the lower hinge arm.

    The bottom pin goes into the arm.

    ▶ Watch this step (2:45)

22. 

    Step 22

    Swing the top hinge arm over the door pin until it clicks.

    Then close the door.

    ▶ Watch this step (2:52)