How to assemble IKEA EKET Cabinet with Door

Step-by-step assembly

1. 

   Step 1

   Sort the four frame panels.

   Two have pegs, two have keyhole slots. The peg panel marked 1 is the top.

   ▶ Watch this step (0:19)

2. 

   Step 2

   Screw the push-opener (139468) to a keyhole panel with 2 screws (108444).

   Use the panel with the pre-drilled holes. Then push in the plunger (139467) until it clicks.

   ▶ Watch this step (0:25)

3. 

   Step 3

   Stand the other keyhole panel on edge and slide a peg panel down onto it.

   The 3 pegs go into the keyhole slots — press down firmly.

   ▶ Watch this step (0:34)

4. 

   Step 4

   Slide the panel with the push-opener down onto the pegs.

   ▶ Watch this step (0:43)

5. 

   Step 5

   Slide the back panel into the grooves.

   Make sure it runs in the grooves, not on top of them.

   ▶ Watch this step (0:50)

6. 

   Step 6

   Slide the last peg panel down to close the frame, then turn it over.

   ▶ Watch this step (0:57)

7. 

   Step 7

   Panel 1 goes at the top. Push the back panel fully into the bottom groove.

   ▶ Watch this step (1:06)

8. 

   Step 8

   Fit a clip (10093081) at the bottom centre of the back panel.

   Then press a wedge (10093082) into the clip.

   ▶ Watch this step (1:12)

9. 

   Step 9

   Fit the other 3 clips: top centre and one on each side.

   Press a wedge (10093082) into each one.

   ▶ Watch this step (1:19)

10. 

    Step 10

    Door hinged on the right? Turn the cabinet over so panel 1 is at the bottom.

    For a door hinged on the left, keep panel 1 at the top (manual p. 13).

    ▶ Watch this step (1:27)

11. 

    Step 11

    Fit legs or a suspension rail — follow its own manual.

    Legs and suspension rail are sold separately (manual p. 12).

    ▶ Watch this step (1:33)

12. 

    Step 12 · manual step 10

    Press 2 wall connectors (141413) into the back, just below the top.

    ▶ Watch this step (1:40)

13. 

    Step 13 · manual step 11

    Drill through the back panel at each connector with a Ø 8 mm bit.

    Ø 8 mm = 5/16".

    ▶ Watch this step (1:48)

14. 

    Step 14 · manual step 12

    Turn a knob (141414) onto each connector.

    Turn it clockwise.

    ▶ Watch this step (1:54)

15. 

    Step 15 · manual step 13

    Move the cabinet to the wall.

    Turn both knobs until they touch the wall, clear of the skirting board.

    ▶ Watch this step (2:00)

16. 

    Step 16 · manual step 14

    Screw through each plate (152651) into the wall.

    Wall screws are not included — choose screws for your wall type.

    ▶ Watch this step (2:07)

17. 

    Step 17 · manual step 15

    Press a cover cap (152650) onto each plate and turn it to lock.

    ▶ Watch this step (2:15)

18. 

    Step 18 · manual step 16

    Press 2 hinge bushings (10119600) into the top and bottom panels.

    At the front corner on the hinge side.

    ▶ Watch this step (2:22)

19. 

    Step 19 · manual step 17

    Click a hinge arm (10119658) into each bushing.

    ▶ Watch this step (2:28)

20. 

    Step 20 · manual step 18

    Screw the washer (101313) and a screw (108444) into the door.

    Lay the door down inside face up.

    ▶ Watch this step (2:34)

21. 

    Step 21 · manual step 19

    Push the hinge pins into the door: 139477 on top, 133127 below.

    ▶ Watch this step (2:42)

22. 

    Step 22 · manual step 20

    Set the door onto the lower hinge arm.

    The bottom pin goes into the arm.

    ▶ Watch this step (2:48)

23. 

    Step 23 · manual step 21

    Swing the top hinge arm over the door pin until it clicks.

    Then close the door.

    ▶ Watch this step (2:55)