How to assemble IKEA BAGGEBO Cabinet with Door

Step-by-step assembly

1. 

   Step 1

   Screw the magnetic catch (103651) to the top panel.

   2 screws (109558). Left-door version shown (p. 12–23); for a right-hand door use p. 24–35.

   ▶ Watch this step (0:20)

2. 

   Step 2

   Push 4 wooden dowels (101345) into the ends of the divider.

   2 in each end.

   ▶ Watch this step (0:29)

3. 

   Step 3

   Fit the top and bottom panels onto the divider.

   Catch towards the front edge — check the close-up in the manual, step 3.

   ▶ Watch this step (0:35)

4. 

   Step 4

   Push 4 dowels into the panel ends and fit a side panel.

   2 dowels in each end, then press the side on.

   ▶ Watch this step (0:43)

5. 

   Step 5

   Screw in 4 screws (100229) with the Allen key (100006).

   2 into the top panel and 2 into the bottom.

   ▶ Watch this step (0:51)

6. 

   Step 6

   Push 2 dowels into the divider and fit the shelf.

   ▶ Watch this step (0:58)

7. 

   Step 7

   Push 6 dowels into the free ends and fit the other side.

   2 each in the top, shelf and bottom.

   ▶ Watch this step (1:05)

8. 

   Step 8

   Screw in 4 more screws (100229) with the Allen key.

   2 into the top panel and 2 into the bottom.

   ▶ Watch this step (1:14)

9. 

   Step 9

   Lay the back panel on the frame.

   Line it up flush with the edges — see the manual’s detail in step 9.

   ▶ Watch this step (1:21)

10. 

    Step 10 · manual step 9

    Nail it on with 14 nails (101221).

    Hold each nail in the nail holder (105493) while you hammer.

    ▶ Watch this step (1:26)

11. 

    Step 11 · manual step 10

    Tap 4 glides (122628) into the bottom ends with a hammer.

    2 in each side panel.

    ▶ Watch this step (1:35)

12. 

    Step 12 · manual step 11

    Stand the cabinet upright.

    ▶ Watch this step (1:42)

13. 

    Step 13 · manual step 11

    Screw the wall bracket (106989) under the top.

    With a washer (100823) and screw (109041) — check the right/wrong detail in the manual, step 11.

    ▶ Watch this step (1:47)

14. 

    Step 14 · manual step 12

    Fix the bracket to the wall through a washer (100823).

    Wall screws and plugs are not included — use ones suited to your wall.

    ▶ Watch this step (1:55)

15. 

    Step 15 · manual step 13–14

    Press in 2 hinge bushings (10119600), then 2 hinge plates (10119658).

    One at the top and one at the bottom, front corner of the door side.

    ▶ Watch this step (2:03)

16. 

    Step 16 · manual step 15

    Screw the washer (101313) onto the door with screw 101068.

    Lay the door inside-up; the washer goes at the corner shown in the manual.

    ▶ Watch this step (2:12)

17. 

    Step 17 · manual step 16

    Push the hinge pins into the door: 139477 on top, 133127 below.

    The top pin is the one with the spring.

    ▶ Watch this step (2:19)

18. 

    Step 18 · manual step 17–18

    Set the lower pin in the bottom plate, then click the top pin in.

    Push the top pin down and slide the door in until it clicks.

    ▶ Watch this step (2:26)

19. 

    Step 19

    Fit the knob (10062514) with screw 119976.

    The screw goes through the door from the inside.

    ▶ Watch this step (2:35)

20. 

    Step 20

    Close the door — the magnetic catch holds it shut.

    If needed, the door can be adjusted at the hinges — see the last page of the manual.

    ▶ Watch this step (2:42)