How to assemble IKEA STRANDTORP Extendable Table

Step-by-step assembly

1. 

   Step 1

   Join 2 legs to a crossbar with 8 screws (10060059).

   4 screws at each corner, tightened with the Allen key. Check which way the bracket faces (manual step 1).

   ▶ Watch this step (0:16)

2. 

   Step 2

   Build the second leg frame the same way.

   Another 8 screws (10060059). Mind the bracket direction shown in step 2.

   ▶ Watch this step (0:25)

3. 

   Step 3

   Tap a foot cap (10060254) into the end of each leg.

   Use the hammer.

   ▶ Watch this step (0:33)

4. 

   Step 4

   Push an end piece (10046075) into one end of each long rail.

   ▶ Watch this step (0:40)

5. 

   Step 5

   Slide a strip (10043121) into each rail.

   ▶ Watch this step (0:46)

6. 

   Step 6 · manual step 6–7

   Stand both rails onto the brackets of one leg frame.

   Push them down until they click. Fix each with 2 screws (147075).

   ▶ Watch this step (0:52)

7. 

   Step 7 · manual step 8

   Fit the second leg frame onto the top of the rails.

   Hook it on and fix it with 4 screws (147075).

   ▶ Watch this step (1:01)

8. 

   Step 8

   Stand the frame on its legs — with two people.

   ▶ Watch this step (1:11)

9. 

   Step 9

   Pull the frame open to its full length.

   The rails slide out — the manual shows it open from step 11.

   ▶ Watch this step (1:18)

10. 

    Step 10 · manual step 9

    Press the plastic fitting into the underside of one end top.

    Lay the end top face-down on a soft surface.

    ▶ Watch this step (1:23)

11. 

    Step 11 · manual step 10

    Fix it with 1 screw (100211) and the Allen key.

    ▶ Watch this step (1:29)

12. 

    Step 12 · manual step 11–12

    Turn it over and set it onto the frame, then slide it outwards.

    Its 4 pegs drop into the rails and run to the end.

    ▶ Watch this step (1:35)

13. 

    Step 13 · manual step 13–14

    Place the second end top the same way and slide it out.

    ▶ Watch this step (1:45)

14. 

    Step 14 · manual step 15

    Screw each end top to its leg frame from below.

    4 screws (100325) — 2 at each end — with the Phillips screwdriver.

    ▶ Watch this step (1:53)

15. 

    Step 15 · manual step 16

    Screw 4 clips (10043084) under each leaf, 2 screws each.

    Lay both leaves face-down. 16 screws (100325) in total.

    ▶ Watch this step (2:02)

16. 

    Step 16 · manual step 17–18

    Lay the first leaf into the gap and push it to the end top.

    4 pegs line up the joint.

    ▶ Watch this step (2:11)

17. 

    Step 17 · manual step 19–20

    Lower the second leaf into the gap and push the table together.

    Its clips hook onto the rails (manual step 19).

    ▶ Watch this step (2:20)

18. 

    Step 18 · manual step 21

    Close the 6 locks under the joints.

    2 locks at each joint.

    ▶ Watch this step (2:28)