How to assemble IKEA NORDVIKEN Extendable Table

Step-by-step assembly

1. 

   Step 1

   Fit a leaf lock (10004568) into each slide crossbar.

   2 screws (122925) per lock — Phillips screwdriver.

   ▶ Watch this step (0:22)

2. 

   Step 2

   Fix 2 runners onto each crossbar.

   Per runner: 1 dowel (101350) and 2 screws (109546). Not the longer 109548.

   ▶ Watch this step (0:28)

3. 

   Step 3 · manual step 3–5

   Build 2 U-frames: a notched cross rail and 2 side boards.

   Cam bolt (118331) in each board, dowels (101350) in the rail ends, then lock with 2 cam locks (110630).

   ▶ Watch this step (0:36)

4. 

   Step 4 · manual step 6

   Screw 2 blocks (10069933) onto each cross rail.

   2 screws (109565) per block.

   ▶ Watch this step (0:45)

5. 

   Step 5 · manual step 7–8

   Push dowels into the ends of the 2 centre rails, then drop them into the U-frames.

   They sit in the middle notch of both cross rails.

   ▶ Watch this step (0:51)

6. 

   Step 6 · manual step 9

   Hook a stop (10003961) onto each cross rail.

   2 screws (108530) each.

   ▶ Watch this step (0:59)

7. 

   Step 7 · manual step 10

   Screw a corner bracket (122483) to each end of the 2 end rails.

   2 screws (109021) per bracket — not the 105248 ones.

   ▶ Watch this step (1:05)

8. 

   Step 8 · manual step 11–13

   Close each end with an end rail and screw the brackets to the side boards.

   2 more screws (109021) per bracket.

   ▶ Watch this step (1:13)

9. 

   Step 9 · manual step 14

   Push 16 dowels (101350) into the top edges of the frame.

   ▶ Watch this step (1:22)

10. 

    Step 10 · manual step 15–16

    Lay the top halves face down on a rug, push them together, add the 2 slides.

    Press each slide’s lock pin into the hole in the top until it clicks.

    ▶ Watch this step (1:28)

11. 

    Step 11 · manual step 17

    Turn the frame over and set it on the top — two people.

    The dowels go into the holes in the top.

    ▶ Watch this step (1:38)

12. 

    Step 12 · manual step 18

    Screw the frame to the top with 18 long screws (154409).

    ▶ Watch this step (1:44)

13. 

    Step 13 · manual step 19–21

    Fit the hinges and clip the 2 side aprons on.

    4 mounting plates (109221) on the top and 4 hinges (109338) on the aprons — 2 screws (105248) each.

    ▶ Watch this step (1:52)

14. 

    Step 14 · manual step 22–24

    Prepare the 4 legs.

    Cross dowel (110912) on top, 2 hanger bolts (100038) in the corner, a bolt (100018) and a dowel low down.

    ▶ Watch this step (2:01)

15. 

    Step 15 · manual step 25

    Fit 2 legs at one end: bolts through the bracket.

    Spring washer (100843) and nut (100712) on each bolt; tighten with the box spanner (120202).

    ▶ Watch this step (2:09)

16. 

    Step 16 · manual step 26–27

    Push 2 cross nuts (10005094) into a low stretcher and fit it between the legs.

    Turn the cross nuts with the Allen key (100092) to pull it tight.

    ▶ Watch this step (2:18)

17. 

    Step 17 · manual step 28–29

    Fit the other 2 legs and the second stretcher the same way.

    ▶ Watch this step (2:27)

18. 

    Step 18 · manual step 30

    Bolt the long stretcher onto the 2 low stretchers.

    2 bolts (100223) with the Allen key.

    ▶ Watch this step (2:36)

19. 

    Step 19 · manual step 31–32

    Tap a glide (117559) onto each leg, and stick 8 felt pads on the top.

    Felt pads (108357) near the ends of the top, 15 mm from the edge.

    ▶ Watch this step (2:43)

20. 

    Step 20 · manual step 33

    Turn the table over onto its legs — two people.

    ▶ Watch this step (2:50)

21. 

    Step 21 · manual step 34–36

    Prepare the 2 leaves: 2 brackets, 2 bolts and 2 felt pads each.

    Brackets 10003975 with 2 screws (109546) each; bolts 157780 by hand.

    ▶ Watch this step (2:56)

22. 

    Step 22 · manual step 37–38

    Pull out both slides, lay a leaf on each and push it in to lock.

    See the manual’s last page for storing the leaves under the top.

    ▶ Watch this step (3:04)