How to assemble IKEA NÄMMARÖ Table

Step-by-step assembly

1. 

   Step 1

   Lay both tabletop halves face down on a rug.

   Work on a soft surface so the top doesn’t get scratched.

   ▶ Watch this step (0:19)

2. 

   Step 2 · manual step 1

   Push 4 pins (113004) into the edge of one half.

   ▶ Watch this step (0:24)

3. 

   Step 3 · manual step 1

   Slide a ring (10065753) onto each pin.

   ▶ Watch this step (0:30)

4. 

   Step 4 · manual step 2

   Push the two halves together.

   ▶ Watch this step (0:35)

5. 

   Step 5 · manual step 3

   Push 4 dowels (128995) into the long edges.

   Use the short dowels here — not 128832.

   ▶ Watch this step (0:40)

6. 

   Step 6 · manual step 4

   Place the 2 long rails onto the dowels.

   The rails are marked C — see the manual, step 4.

   ▶ Watch this step (0:46)

7. 

   Step 7 · manual step 5

   Fix the rails with 12 bolts (117794).

   Use the Allen key.

   ▶ Watch this step (0:53)

8. 

   Step 8 · manual step 6

   Push 8 dowels (128832) into the ends of the rails.

   ▶ Watch this step (1:01)

9. 

   Step 9 · manual step 7

   Slide an end frame onto the rail ends.

   ▶ Watch this step (1:07)

10. 

    Step 10 · manual step 8

    Push 2 cross dowels (113153) into the rails.

    Turn them with a flat screwdriver so the hole lines up.

    ▶ Watch this step (1:12)

11. 

    Step 11 · manual step 8

    Screw 2 bolts (113134) through the legs into the rails.

    Use the Allen key.

    ▶ Watch this step (1:18)

12. 

    Step 12 · manual step 9

    Fix the end frame to the top with 3 bolts (117794).

    ▶ Watch this step (1:25)

13. 

    Step 13 · manual step 10–12

    Fit the other end frame the same way.

    Cross dowels 113153, bolts 113134, then 3 bolts 117794 (steps 10–12).

    ▶ Watch this step (1:31)

14. 

    Step 14 · manual step 13

    Lower the 2 braces into place.

    Their flat ends sit on the centre of the top.

    ▶ Watch this step (1:42)

15. 

    Step 15 · manual step 13

    Fix each brace to the top with a bolt (105089).

    ▶ Watch this step (1:48)

16. 

    Step 16 · manual step 14

    Push a cross dowel (113107) into the end of each brace.

    Line up the hole with a flat screwdriver.

    ▶ Watch this step (1:54)

17. 

    Step 17 · manual step 14

    Bolt the braces to the end frames (105089).

    Through the bottom rail of each end frame.

    ▶ Watch this step (1:59)

18. 

    Step 18 · manual step 15

    Hold the centre bar against the tops of the braces.

    Use the bar shown in the manual, step 15.

    ▶ Watch this step (2:05)

19. 

    Step 19 · manual step 15

    Put a spacer (10089502) between the bar and the brace.

    ▶ Watch this step (2:11)

20. 

    Step 20 · manual step 15

    Push a bolt (10089487) through the bar, spacer and brace.

    Use the Allen key.

    ▶ Watch this step (2:16)

21. 

    Step 21 · manual step 15

    Add a 2nd spacer, washer (113135) and nut (113149).

    Tighten the nut with the spanner (108184) — see the manual, step 15.

    ▶ Watch this step (2:22)

22. 

    Step 22 · manual step 16

    Bolt the other end of the bar to the other brace.

    Spacer, bolt 10089487, spacer, washer 113135 and nut 113149.

    ▶ Watch this step (2:30)

23. 

    Step 23 · manual step 17

    Turn the table over onto its legs.

    ▶ Watch this step (2:39)