How to assemble IKEA RAMNEFJÄLL Upholstered Bed Frame

Step-by-step assembly

1. 

   Step 1

   Lay the headboard face down; bolt on the 4 braces.

   4 bolts (105109) through the sides. Use Allen key 130445 in the handle (10050800).

   ▶ Watch this step (0:16)

2. 

   Step 2

   Fit the centre bar with 2 bolts (105109).

   ▶ Watch this step (0:23)

3. 

   Step 3

   Fit the bottom rail with 3 bolts (105109).

   One at each end and one into the centre bar.

   ▶ Watch this step (0:29)

4. 

   Step 4

   Bolt a block inside each post: 4 bolts (105109).

   ▶ Watch this step (0:36)

5. 

   Step 5

   Turn the headboard over; fit 1 bolt (105102) with the washer (100837).

   In the middle, just above the bottom edge of the padded panel.

   ▶ Watch this step (0:42)

6. 

   Step 6

   Lay the footboard face down; screw in 4 bolts (105102) part-way.

   Leave a gap under the heads — don’t screw them flush.

   ▶ Watch this step (0:50)

7. 

   Step 7

   Hook a block onto each pair of bolts, slide it and tighten.

   Through the keyholes with Allen key 130445.

   ▶ Watch this step (0:57)

8. 

   Step 8

   Screw 10 bolts (105102) part-way into the headboard and footboard.

   2 into each block and 1 in the middle of each — leave a gap under the heads.

   ▶ Watch this step (1:04)

9. 

   Step 9

   Stand the headboard up and hang both side rails on it.

   The keyhole plates drop over the bolt heads. The rails’ other ends stay loose for now.

   ▶ Watch this step (1:12)

10. 

    Step 10

    Stand the footboard up and lower it onto the rail ends.

    ▶ Watch this step (1:22)

11. 

    Step 11

    Tighten the bolts at the headboard corners.

    Through the keyhole plates — Allen key 130445 in the handle.

    ▶ Watch this step (1:29)

12. 

    Step 12

    Fit the cross bar under the rail ledges.

    2 spacers (10088054) on top, 2 bolts (105109) from below.

    ▶ Watch this step (1:35)

13. 

    Step 13

    Hook the centre beam onto the middle bolts; add 2 bolts (105102).

    In the upper holes of the end plates, then tighten all four.

    ▶ Watch this step (1:43)

14. 

    Step 14

    Bolt the cross bar to the beam from below: 1 bolt (105109).

    ▶ Watch this step (1:51)

15. 

    Step 15

    Screw the long bolt (10073108) down through the centre beam.

    With the large Allen key (108490). It goes into the support leg — see the manual, step 15.

    ▶ Watch this step (1:57)

16. 

    Step 16

    Pull the cover down over the headboard.

    ▶ Watch this step (2:04)

17. 

    Step 17 · manual step 17–19

    Fold the cover around the legs and close it at the back.

    Velcro at the sides and bottom, then the zip at the back — see the manual, steps 17–19.

    ▶ Watch this step (2:11)

18. 

    Step 18 · manual step 20

    Pull the cover over the footboard; fold it under.

    Close the Velcro under the bottom edge.

    ▶ Watch this step (2:18)

19. 

    Step 19 · manual step 21

    Fit the side covers over the rails.

    Head end first, then the foot end, then the middle — tuck the edge in along the ledge.

    ▶ Watch this step (2:24)

20. 

    Step 20 · manual step 22

    Push 8 clips (10096290) into the ledges and the beam.

    Push in, then slide them toward the ends.

    ▶ Watch this step (2:32)

21. 

    Step 21 · manual step 23

    Roll out the slatted bed base (Luröy) from head to foot.

    Tuck the end slats under the clips.

    ▶ Watch this step (2:39)