How to assemble IKEA FYRESDAL Daybed Frame

Step-by-step assembly

1. 

   Step 1

   Lay the backrest flat and push the 2 leg tubes onto its posts.

   Line the holes up as shown in the manual.

   ▶ Watch this step (0:16)

2. 

   Step 2

   Lock each leg with 1 screw (122898).

   Allen key 111631.

   ▶ Watch this step (0:22)

3. 

   Step 3 · manual step 3–4

   Build both armrests the same way: leg tube on, 1 screw each.

   Screws 122898.

   ▶ Watch this step (0:29)

4. 

   Step 4

   Stand the backrest up.

   ▶ Watch this step (0:37)

5. 

   Step 5

   Bolt the armrests to the backrest posts: 4 bolts (146767).

   Use the long bolts 146767 here, not 131182.

   ▶ Watch this step (0:42)

6. 

   Step 6 · manual step 6–7

   Fit a centre leg to the rail with the handles: 2 screws (122898).

   Use the leg shown in step 6 — the other one is for step 8.

   ▶ Watch this step (0:51)

7. 

   Step 7 · manual step 8–9

   Fit the other centre leg to the plain rail: 2 screws.

   Check the rail’s hole pattern against the manual (page 8).

   ▶ Watch this step (0:59)

8. 

   Step 8 · manual step 10

   Screw the 2 glides (117229) into the centre legs.

   ▶ Watch this step (1:06)

9. 

   Step 9 · manual step 11

   Screw the 3 cross bars onto the handle rail — 2 screws each.

   Use the 3 bars with a plate, not the 2 similar ones. Screws 122898.

   ▶ Watch this step (1:12)

10. 

    Step 10 · manual step 12

    Turn both rails up onto their legs.

    ▶ Watch this step (1:21)

11. 

    Step 11 · manual step 13

    Push the plain rail onto the ends of the 3 cross bars.

    ▶ Watch this step (1:27)

12. 

    Step 12 · manual step 14–16

    Fit the last rail to the bar ends with 3 studs (131182).

    Screw them in by hand, then tighten with the Allen key — they must stand out, not sink in.

    ▶ Watch this step (1:32)

13. 

    Step 13 · manual step 17

    Push the rod with the threaded end through; fix it with 1 screw.

    Screw 122898 — tightened later, in step 20.

    ▶ Watch this step (1:41)

14. 

    Step 14 · manual step 18

    Push the 2 other rods through the rail.

    ▶ Watch this step (1:48)

15. 

    Step 15 · manual step 19

    With 2 people, lift the backrest on — the 3 rods go into its rail.

    ▶ Watch this step (1:54)

16. 

    Step 16 · manual step 20

    Fix the centre rod at the back with 1 screw (122898).

    Then tighten the screw at the front rail from step 17.

    ▶ Watch this step (2:01)

17. 

    Step 17 · manual step 21

    Bolt the armrest legs to the front rail: 4 bolts (146767).

    ▶ Watch this step (2:09)

18. 

    Step 18 · manual step 22

    Click a plastic slide (146967) onto the end of each long tube.

    The tube’s end hole must face as shown in step 22.

    ▶ Watch this step (2:16)

19. 

    Step 19 · manual step 23

    Lay the 2 tubes in and screw their plates to the handle rail.

    1 screw (122898) per tube.

    ▶ Watch this step (2:22)

20. 

    Step 20 · manual step 24

    Screw the slides down: 2 screws (128874), small Allen key 100001.

    ▶ Watch this step (2:31)

21. 

    Step 21 · manual step 25

    Lay the 34 slats with the small holes in the back part.

    Ends into the backrest rail, then 17 clips (146865) — press until they click.

    ▶ Watch this step (2:38)

22. 

    Step 22 · manual step 26

    Lay the 36 plain slats in the pull-out part; 18 clips.

    Ends into the holes of the handle rail, clips at the other end.

    ▶ Watch this step (2:47)

23. 

    Step 23

    Push the pull-out part in — your daybed is ready.

    Manual pages 23–24 show how to pull it out for a double bed.

    ▶ Watch this step (2:56)