IKEA · Beds

How to assemble IKEA FLEKKE Daybed Frame with 2 Drawers

Step-by-step IKEA FLEKKE Daybed Frame with 2 Drawers assembly: 26 illustrated steps, an animated video, the hardware list and the tools you need — following the official instructions (AA-1866851-18).

  • 26 illustrated steps
  • 52 steps in the manual
  • 3:29 video
  • 198×102×80 cm
IKEA FLEKKE Daybed Frame with 2 Drawers, assembled

What you need

Tools

  • Flat-head screwdriver
  • Phillips screwdriver
  • Hammer

Hardware in the box

Part no. (as printed in the manual)Qty
1394308×
1002153×
10136710×
1146708×
10530751×
1003724×
11052527×
1304852×
1236602×
1307875×
10135024×
11833124×
11063016×
10904916×
10034724×
1105198×
1013458×
1190308×
1003594×
1066984×

Step-by-step assembly

  1. Step 1: Section 1 · frame. 4 dowels in the long panel, 4 bolts in the ends. — IKEA FLEKKE assembly

    Step 1 · manual step 1–2

    Section 1 · frame. 4 dowels in the long panel, 4 bolts in the ends.

    Dowels 101367. Bolts 139430 — tighten with the wrench (113453). Corner on the left? Manual p. 18–29.

  2. Step 2: Fit 4 connectors (114670), stand the panels up, tighten. — IKEA FLEKKE assembly

    Step 2 · manual step 3–4

    Fit 4 connectors (114670), stand the panels up, tighten.

    Allen key 100049 — tighten in the order shown in the manual.

  3. Step 3: Screw 2 brackets (130485) inside the ends, fit the front bar. — IKEA FLEKKE assembly

    Step 3 · manual step 5

    Screw 2 brackets (130485) inside the ends, fit the front bar.

    Bar 112978. 4 screws (105307) — not 100372.

  4. Step 4: 4 more connectors. Bolts and dowels into the 2 backrest panels. — IKEA FLEKKE assembly

    Step 4 · manual step 6–8

    4 more connectors. Bolts and dowels into the 2 backrest panels.

    Connectors 114670, bolts 139430 (wrench 113453), dowels 101367.

  5. Step 5: Set both backrest panels on top. Tighten, add 3 corner screws. — IKEA FLEKKE assembly

    Step 5 · manual step 9–12

    Set both backrest panels on top. Tighten, add 3 corner screws.

    Connectors: Allen key 100049. Screws 100215: Allen key 100001.

  6. Step 6: With 2 people, lay the frame on its back. Screw on the slat rail. — IKEA FLEKKE assembly

    Step 6 · manual step 13–15

    With 2 people, lay the frame on its back. Screw on the slat rail.

    Rail 112976: 2 + 6 screws (105307).

  7. Step 7: Screw a bracket (123660) onto 2 long slats. Fit them at the ends. — IKEA FLEKKE assembly

    Step 7 · manual step 16–17

    Screw a bracket (123660) onto 2 long slats. Fit them at the ends.

    Bracket screws 100372; 4 screws 105307 into the rails.

  8. Step 8: Push a pin (110525) into 11 slats. Fit them, 11 screws (105307). — IKEA FLEKKE assembly

    Step 8 · manual step 18–19

    Push a pin (110525) into 11 slats. Fit them, 11 screws (105307).

    Pins into the back rail, screws into the front bar.

  9. Step 9: Tap 5 glides (130787) into the bottom edges. Stand the frame up. — IKEA FLEKKE assembly

    Step 9 · manual step 20

    Tap 5 glides (130787) into the bottom edges. Stand the frame up.

    Don’t sit on the frame before the pull-out bed is under it.

  10. Step 10: Section 2 · pull-out bed. Slat rail, then 8 cam bolts (118331). — IKEA FLEKKE assembly

    Step 10 · manual step 21–23

    Section 2 · pull-out bed. Slat rail, then 8 cam bolts (118331).

    Rail 112976: 8 screws (105307). Then 8 dowels (101350) into the end panels.

  11. Step 11: Stand the end panels up on the back panel. Lock 4 cam locks. — IKEA FLEKKE assembly

    Step 11 · manual step 24–25

    Stand the end panels up on the back panel. Lock 4 cam locks.

    Cam locks 110630 — turn clockwise with the flat screwdriver.

  12. Step 12: Screw 2 castors (111401) under each of the 4 beams. 16 dowels. — IKEA FLEKKE assembly

    Step 12 · manual step 26–27

    Screw 2 castors (111401) under each of the 4 beams. 16 dowels.

    16 screws (109049). Mind the hole pattern in the beam ends — manual step 26.

  13. Step 13: Stand the 4 beams up on the back panel. Lock 4 cam locks. — IKEA FLEKKE assembly

    Step 13 · manual step 28–29

    Stand the 4 beams up on the back panel. Lock 4 cam locks.

    Cam locks 110630.

  14. Step 14: Front panel: slat rail (8 × 105307), then 8 cam bolts (118331). — IKEA FLEKKE assembly

    Step 14 · manual step 30–31

    Front panel: slat rail (8 × 105307), then 8 cam bolts (118331).

  15. Step 15: Turn the front panel over onto the unit. Lock 8 cam locks. — IKEA FLEKKE assembly

    Step 15 · manual step 32–33

    Turn the front panel over onto the unit. Lock 8 cam locks.

    Cam locks 110630: 4 in the end panels, 4 in the beams.

  16. Step 16: Screw the 4 drawer runners (139505) onto the beams. — IKEA FLEKKE assembly

    Step 16 · manual step 34

    Screw the 4 drawer runners (139505) onto the beams.

    3 screws (100347) each — not 105307.

  17. Step 17: Screw on 4 of the 12 short slats: 8 screws (105307). — IKEA FLEKKE assembly

    Step 17 · manual step 35

    Screw on 4 of the 12 short slats: 8 screws (105307).

    Positions as shown in manual step 35.

  18. Step 18: Turn the pull-out bed upright. Pin the other 8 slats and lay them in. — IKEA FLEKKE assembly

    Step 18 · manual step 36–37

    Turn the pull-out bed upright. Pin the other 8 slats and lay them in.

    16 pins (110525) go into the holes in the slat rails.

  19. Step 19: With 2 people, slide the pull-out bed under the frame. — IKEA FLEKKE assembly

    Step 19 · manual step 38

    With 2 people, slide the pull-out bed under the frame.

    See the manual, step 38.

  20. Step 20: Section 3 · drawers. 4 dowels (101345), 4 cam bolts (118331). — IKEA FLEKKE assembly

    Step 20 · manual step 39–40

    Section 3 · drawers. 4 dowels (101345), 4 cam bolts (118331).

    Dowels in the sides, cam bolts in the drawer front. One drawer shown.

  21. Step 21: Put the sides onto the front. Lock 4 cam locks (119030). — IKEA FLEKKE assembly

    Step 21 · manual step 41–42

    Put the sides onto the front. Lock 4 cam locks (119030).

  22. Step 22: Screw 1 screw (100359) into the front, hook on the bar (120030). — IKEA FLEKKE assembly

    Step 22 · manual step 43–45

    Screw 1 screw (100359) into the front, hook on the bar (120030).

    Leave a small gap under the screw head. Then slide the bottom in.

  23. Step 23: Fit the back. Tap in 4 screw dowels (110519), add 1 screw (100359). — IKEA FLEKKE assembly

    Step 23 · manual step 46–48

    Fit the back. Tap in 4 screw dowels (110519), add 1 screw (100359).

  24. Step 24: Turn the drawer over. Screw on the runners DR and DL. — IKEA FLEKKE assembly

    Step 24 · manual step 49–51

    Turn the drawer over. Screw on the runners DR and DL.

    3 screws (100347) each. Bumpers (107091) and 2 stops (106698): manual steps 49 and 51.

  25. Step 25: Build the second drawer the same way. — IKEA FLEKKE assembly

    Step 25 · manual step 39–51

    Build the second drawer the same way.

  26. Step 26: Slide both drawers into the pull-out bed. — IKEA FLEKKE assembly

    Step 26 · manual step 52

    Slide both drawers into the pull-out bed.

Tips & safety

  • Don’t sit on the frame before the pull-out bed is under it. See the warning on manual p. 17.
  • Never step or stand on an open drawer. See the warning on the last page of the manual.

Official instructions

This guide follows IKEA’s official assembly instructions (AA-1866851-18). Keep the printed manual to hand — if anything differs, the manual is right.

Open the official PDF manual

More guides: Beds

MALM Bed Frame
MALMBed Frame18 steps · 3:01 video
KURA Reversible Bed
KURAReversible Bed23 steps · 3:24 video
TARVA Bed Frame
TARVABed Frame17 steps · 2:41 video
HEMNES Daybed Frame with 3 Drawers
HEMNESDaybed Frame with 3 Drawers28 steps · 3:32 video